| Estimate the number of people needed to carry cell phone made of vacuum tubes. |
| With the energy consumed by the vacuum tube cellphone how many houses could you light up? |
| Plot the Arrhenius equation vs temperature and note down what happens around 300K when there is slight change in temp. |
| f(v+t/2) =0.5 f(v),starting from this point generate exponential |
| Arrhenius equation-Do it in EXCEL -How does it behaves with Eg |
| What is the maximum radius of the smaller circle? |
| What is the size of the 3D object? |
| Can we rotate the smaller circle? |
Thursday, May 17, 2012
Others
AC
| draw a waveform such that ac=0,bc=0 and c not identically 0,where a b c are square waveforms. |
| RMS voltage |
| Power waveform |
| deference between Avg Power,RMS power,instantaneous power |
| differentiation and integration of power waveform. |
| low pass filter |
| Digital waveforms are short and coupling with analog signals is easy?Why? |
| Calculation of w (omega) |
analog
| Inverter transfer characteristics |
| Sakurai model for inverter delay calculation and also error introduced (between the sakurai model and the actual characteristics) |
| Bode plots for multi stage RC and RLC network. |
| Bode plot for the transfer characteristic of electric network. |
| When waveform is pulsating then what is output impedence of the circuit |
| When both p and n are off, then how does pulse waveform act on inductor and capacitor? |
| Star and delta configuration in transformer |
| Cis Ө |
| Laplace transform |
| deferential equations,differentiation |
| if current and voltages are at 90 degree phase shift,then what is the power? |
| calculation of capacitor impedance |
| What is the voltage swing in ECL gate? |
| For constant n channel impedance, draw the output curves for different pMOS w/l ratios i.e different impedances of pMOS |
| Spice and sub-circuit for 555, 741 op-amp |
Data Path,I/O and Memory
| Variation of delay of inverter chain wrt fanout numbers |
| Find internal fan out of an inverter. |
| Find optimum number of stages to obtain minimum delay. |
| Find out fan out for basic gates. |
| Obtain differential equation solution for finding optimum point on delay curve. |
| Find Cin, Cload, Cdiode, Cabrupt, Cox and Cmetal of an an inverter. |
| Plot graph for delay Vs fan out. |
| Derive relation between gm and gds. |
| Prove that gm is a function of id. |
| Excel work on fourier representation of square wave. |
| Design of Tri-state buffers to control universal bus. |
| Find the width 'W1' in the following figure in order to maintain the same current which flows when the width is W. |
| I/O buffers:Resistor calculation,Vg,Sat region,Linear and Saturation |
| DRAM-Cross section:topography,Planarisation |
| What happens when Metal 1 and Metal 2 are kept-far,near and at a little distance? |
| What will be the problem when thay are kept at some distance |
| Fan-out |
| capacitance as a function of width |
| area cap and perimeter cap |
| Tristate Buffer Spice? |
| For different Fanin/ Fanout ratio plot a efficiency curve for same load |
| transmission gate in CMOS |
Transistors
| delsquare phi=0 | |
|
|
| NMOS characteristics - id/vds, id/vgs (done i hope) | |
| Variation of voltage across the channel (channel voltage profile) | |
| Vt as a function of back bias voltage,back oxide thickness,front oxide thickness,doping in the channel | |
| variation of Vt wrt Vbulk volt | |
| Calculating AD, AS, PD, PS | |
| Vt reduction as length reduces | |
| Depletion width in a bulk semiconductor-equation and graph | |
| If poly contact breaks then what happens to the circuit operation? | |
| Highly coupled and loosely coupled circuits | |
| Series resistor with capacitor | |
| voltage source with capacitor | |
| Changing the supply for a inverter like 3.3v , 5v , 4v | |
| In one cm how many Si atoms are there? | |
| What is the cost of chip having 1cm size and 1um thickness? | |
| Calculation of Si-Si,Si-Boron and Boron-Boron distance? | |
| How many Si atoms are put in the cube during doping time? | |
| Acceleration graph | |
| If the input to a transmission line is sine wave and square wave. In which case crosstalk between lines is more? | |
| Design a CMOS MUX using transmission gates? | |
| Design three combinational circuits using CMOS transmission gates . | |
| What is the total no. of transistors of types nMOS,pMOS and of both can be fabricated on a 1X1 cm chip? | |
| Solve by excel the decrease in charge occurring due to diffusion. | |
| Solve by excel the decrease in charge occurring due to diffusion. | |
| Vt of nMOS =0.6v , Vt of pMOS =0.7v power supply is =1.3v draw the output characteristics also draw curve when Vtn=Vtp=0.7v and supply = 1v | |
| How many molecules of SiO2 can we see in a 0.2X0.2 micron surface? | |
| What is the breakdown voltage of oxide layer 100 angstrom thick? | |
| Analyze an inverter output if the supply voltage is Vdd=0.6+0.7 V. | |
| Analyze an inverter output if the supply voltage is Vdd=1V. | |
| In the Ids versus Vds curve if we extrapolate the exponential curve to linear curve at Ids saturation what is the value Vds at that point | |
| In the output characteristics of an inverter what is the slope of curve at centre with Model 2 MOS? | |
| Design a 10ohm resistor Vg=5v Vds=0 . | |
| Find the current in between Vtn and Vtp in output characteristic of inverter (derive it) | |
| For a nMOS in series with capacitor draw Id versus Vgs at source of nMOS when a sudden rise from 0v to 5v is applied at gate | |
| Find the equation of Vt for model 1. | |
| Why should you merge always towards drain?-Capacitance | |
| If a current source is charging a capacitor then what is output voltage? | |
| What is the current in the circuit and how does it change? | |
| What happens is width is increased 4 times? | |
|
|
| What happens when fingering is done? |
RC
| RC voltage characteristics |
| Capacitor discharging through NOMS |
| Charging of capacitor with constant current source |
| Capacitor distance is more then what is voltage and charge? |
| If distance between parallel plate cap doubled then what changes occurs in electric field,energy,voltage and capacitor |
| Distance is same the find charge,enery and voltage |
| Checking the inverter with cap simulation |
| Using EXCEL perform an RC circuit analysis such that max error is 1%. |
| Assuming a small resistance calculate the current and energy dissipated over 0 to ½ CV 2. |
| Derive an expression to find capacitance of a cable. |
| If C=10microfared,V=5v,R=315360000,how many electrons will flow away from capacitor everyday ? |
| Find the capacitance of two spheres placed concentrically. |
| For the 1-exp charging wave find t1 and t2? |
| Download field solver set up the capacitor problem and then solve it. |
| Plot the waveform in EXCEL -for NMOS supplied by a current source which has a capacitor across it |
Graphs
| 1) Analysis of differentiation and integrations(For a given equations ). |
| 2) Differentiate and integrate sine wave? |
| 3) Graph for ohmic and non-ohmic devices |
| 4) How did the pyramids get corners with exact 90 o ? |
| 5) Solve by excel that a square wave can be represented as a sum of sine waves of 3,5,7..... harmonics. |
| 6) Using EXCEL GOAL SEEK Function plot sine wave added with harmonics to represent square wave. |
| 7) Integration of Different curves |
| 8) Extrapolate the linear curve of the 1-exp wave and extend saturated line to meet the curve and find the corresponding voltage. |
| 8) Derive the equation for growth of oxide relating initial and final rate. |
| 9) IV characteristics for Neon bulb.Can we change the curve along |
| 10) X and Y axis. Integrate the curve |
| 11) Determine the change of region between linear and saturation in the graph |
| 12) Generate waveform for 555 timer |
| 13) Transition & Diffusion in excel |
| 14) Linear & abrupt change |
| 15) What is the depletion width when concentration crosses zero? |
Wednesday, May 16, 2012
Broken Umbrella
1 What is linear junction and abrupt junction?
2 Annealing
More Information.
http://c2.com/cgi/wiki?KnowledgeAnnealing
3 What is the state of silicon at 0K and at 60K?
4 To read about SP^3 orbitals
abrupt junction
A PN junction
is the juxtaposition of a n-type and a p-type piece of semiconductor,
taken originally from the same block of crystal. The difference between
the densities of donors and acceptors ND - NA
undergoes a very sharp variation from a negative value in the P region
to a positive value in the N region. An abrupt junction is by definition
a junction in which the doping type changes over a very small distance
compared to the spatial extent of the depletion region (see below.)
Figure EC1 : Donor and acceptor density profiles in an abrupt PN junction
There are some other types of junctions
(exponential, linear junctions...). However we will only focus here on
the abrupt junction, because results are much simpler and can be easily
generalized to more complex cases.
Figure EC2 : Diagram showing the electronic bonds in an abrupt P-N
junction of Si. Here N-doping is achieved with arsenic (As) atoms and
P-doping with boron (B) atoms
Figure EC2 enables understanding what
happens when a N-type semiconductor is in contact with a P-type
semiconductor. The electrons, abundant in the N-type region, will cross
the junction in order to recombine with holes present in the P-type
region. Therefore, a negative static space charge builds up in the P
region (the trivalent boron atoms have a static negative charge since
they release a positively-charged hole in the valence band) whereas a
positive space charge builds up in the N-type zone for the same reasons.
The small volume in which this space charge is created is called the space
charge zone or depletion zone.
Because there is a strong electric field in this area, the density of
free carriers is negligible at thermal equilibrium. In addition, the
frontier between the depletion zone and the neutral parts of the
junction is very sharp.
Figure EC3 : P-N junction at thermal equilibrium
Just after the P- and N-type semiconductors
have been drawn closer, a potential barrier appears for both holes an
electrons. Indeed, the static space charges accumulated at the borders
of the junction (positive charges in the N zone, negative charges in the
P zone) create an electric field pointing from N towards P, which
prevents diffusion and further recombination of electrons and holes:
diffusion is then rapidly stopped by the buildup of this internal
electric field. In addition, because of the existence of this double
layer of charges on both sides of the junction, the electrostatic
potential varies sharply inside the depletion zone and the potential
difference Vd, called the diffusion
potential (or built-in potential) reaches non-negligible values (e.g.
0.8V for Si). However, if we attempt to measure a voltage by connecting a
multimeter at both sides of the PN diode, we will find a zero voltage
drop, because a multimeter measures a difference in electrochemical
potentials, not just electrostatic potentials. Indeed, here the
electrochemical potential is constant throughout the crystal, including
in the space charge zone, because this potential takes into account not
only the electric field but also the concentration gradient of charge
carriers. The diffusion potential due to this gradient compensates
exactly for the electrostatic potential.
The relationship between the space p[C X cm^-3]
charge density , the electric field
E
and the electrostatic potential
is :
Where
is the permittivity of the medium (10‑10 F/m for silicon).
The (chemical) potential of a semiconductor being equal to its Fermi energy, the built-in potential or diffusion potential is proportional to the difference of the Fermi energies of the two unbounded semiconductors :
When the junction meets thermal equilibrium,
the Fermi energy has a constant value throughout the whole device. The
energies of conduction and valence bands are therefore shifted up or
down, and exhibit a smooth variation across the depletion region. As a
consequence, there is an electrostatic potential energy difference
appearing between the P and N region, equal to qVd.
More Information.
1) http://www.google.co.in/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&sqi=2&ved=0CFsQFjAB&url=http%3A%2F%2Fwww.ifm.liu.se%2Fcourses%2Ftfyy77%2FCourse%2520Note%2520L3_p-n%2520junction.pdf&ei=AU2zT7GtKsTorAe9urnkAw&usg=AFQjCNGNscC51kPWIQV_HyCV4ffIDHLd1w&sig2=ezcgz5vN36iOfBdeSUDQ9Q
2) http://ecee.colorado.edu/~bart/book/book/chapter4/ch4_2.htm
A pn junction in which the concentration of impurities changes suddenly from acceptors to donors, this is called abrupt junction.
linear junction
2 Annealing
Heating steel to, and
holding at a suitable temperature, followed by relatively slow cooling.
The purpose of annealing may be to remove stresses, to soften the steel,
to improve machinability, to improve cold working properties, to obtain
a desired structure. The annealing process usually involves allowing
the steel to cool slowly in the furnace.
More Information.
http://c2.com/cgi/wiki?KnowledgeAnnealing
3 What is the state of silicon at 0K and at 60K?
4 To read about SP^3 orbitals
PCB STEPS
1 Why inert gas is used in incandescent bulb? How does incandescent bulb works? Why tungsten is used in incandescent bulb?
Light bulbs have a very simple structure. At the base, they have two metal contacts, which connect to the ends of an electrical circuit. The metal contacts are attached to two stiff wires, which are attached to a thin metal filament. The filament sits in the middle of the bulb, held up by a glass mount. The wires and the filament are housed in a glass bulb, which is filled with an inert gas, such as argon. When the bulb is hooked up to a power supply, an electric current
flows from one contact to the other, through the wires and the
filament. Electric current in a solid conductor is the mass movement of free electrons (electrons that are not tightly bound to an atom) from a negatively charged area to a positively charged area.
As the electrons zip along through the filament, they are constantly bumping into the atoms that make up the filament. The energy of each impact vibrates an atom -- in other words, the current heats the atoms up. A thinner conductor heats up more easily than a thicker conductor because it is more resistant to the movement of electrons.
Bound electrons in the vibrating atoms may be boosted temporarily to a higher energy level. When they fall back to their normal levels, the electrons release the extra energy in the form of photons. Metal atoms release mostly infrared light photons, which are invisible to the human eye. But if they are heated to a high enough level -- around 4,000 degrees Fahrenheit (2,200 degrees C) in the case of a light bulb -- they will emit a good deal of visible light.
The filament in a light bulb is made of a long, incredibly thin length of tungsten metal. In a typical 60-watt bulb, the tungsten filament is about 6.5 feet (2 meters) long but only one-hundredth of an inch thick. The tungsten is arranged in a double coil in order to fit it all in a small space. That is, the filament is wound up to make one coil, and then this coil is wound to make a larger coil. In a 60-watt bulb, the coil is less than an inch long.
Tungsten is used in nearly all incandescent light bulbs because it is an ideal filament material. we'll find out why this is, and we'll examine the role of the glass bulb and inert gas.
a metal must be heated to extreme temperatures before it will emit a useful amount of visible light. Most metals will actually melt before reaching such extreme temperatures -- the vibration will break apart the rigid structural bonds between the atoms so that the material becomes a liquid. Light bulbs are manufactured with tungsten filaments because tungsten has an abnormally high melting temperature.
But tungsten will catch on fire at such high temperatures, if the conditions are right. Combustion is caused by a reaction between two chemicals, which is set off when one of the chemicals has reached its ignition temperature. On Earth, combustion is usually a reaction between oxygen in the atmosphere and some heated material, but other combinations of chemicals will combust as well.
The filament in a light bulb is housed in a sealed, oxygen-free chamber to prevent combustion. In the first light bulbs, all the air was sucked out of the bulb to create a near vacuum -- an area with no matter in it. Since there wasn't any gaseous matter present (or hardly any), the material could not combust.
The problem with this approach was the evaporation of the tungsten atoms. At such extreme temperatures, the occasional tungsten atom vibrates enough to detach from the atoms around it and flies into the air. In a vacuum bulb, free tungsten atoms shoot out in a straight line and collect on the inside of the glass. As more and more atoms evaporate, the filament starts to disintegrate, and the glass starts to get darker. This reduces the life of the bulb considerably.
In a modern light bulb, inert gases, typically argon, greatly reduce this loss of tungsten. When a tungsten atom evaporates, chances are it will collide with an argon atom and bounce right back toward the filament, where it will rejoin the solid structure. Since inert gases normally don't react with other elements, there is no chance of the elements combining in a combustion reaction.
Cheap, effective and easy-to-use, the light bulb has proved a monstrous success. It is still the most popular method of bringing light indoors and extending the day after sundown. But by all indications, it will eventually give way to more advanced technologies, because it isn't very efficient.
Incandescent light bulbs give off most of their energy in the form of heat-carrying infrared light photons -- only about 10 percent of the light produced is in the visible spectrum. This wastes a lot of electricity. Cool light sources, such as fluorescent lamps and LEDs, don't waste a lot of energy generating heat -- they give off mostly visible light. For this reason, they are slowly edging out the old reliable light bulb.
2 To read about black body radiation
3 How CFL works?
3 What is meant by non ionizing radiation?
Non-ionizing (or non-ionising) radiation refers to any type of electromagnetic radiation that does not carry enough energy per quantum to ionize atoms or molecules—that is, to completely remove an electron from an atom or molecule. Instead of producing charged ions when passing through matter, the electromagnetic radiation has sufficient energy only for excitation, the movement of an electron to a higher energy state. Nevertheless, different biological effects are observed for different types of non-ionizing radiation

Electromagnetic radiation, the photons of which lack the energy required to ionize atoms or induce ion formation; NIR includes sound, ultraviolet, visible, and infrared light, microwaves, and radiowaves. Cf Ionizing radiation.
4 Which are the types of UV lights? Where all we use UV light?
There are three types in UV Lights, 1) UV-C, 2)UV-B, 3)UV-A
1) UVC - shortwave UV, which includes germicidal ultraviolet at 253.7nm wavelength - is used for air, surface and water disinfection. Unintentional overexposure to UV-C causes skin redness and eye irritation, but does not cause skin cancer or cataracts.
2) UV-B - A small, but dangerous part of sunlight. Most solar UV-B is absorbed by the ozone layer. Prolonged exposure causes sun burn and could result in unhealthy effects on the skin and eyes.
3) UV-A - Long wave UV causes premature skin aging.
9 To read about absorption spectra, emission spectra, hydrogen spectra, EPROM..
10 Difference between dose and intensity
11 Probability calculation in PCB
12 Transistor specifications
As the electrons zip along through the filament, they are constantly bumping into the atoms that make up the filament. The energy of each impact vibrates an atom -- in other words, the current heats the atoms up. A thinner conductor heats up more easily than a thicker conductor because it is more resistant to the movement of electrons.
Bound electrons in the vibrating atoms may be boosted temporarily to a higher energy level. When they fall back to their normal levels, the electrons release the extra energy in the form of photons. Metal atoms release mostly infrared light photons, which are invisible to the human eye. But if they are heated to a high enough level -- around 4,000 degrees Fahrenheit (2,200 degrees C) in the case of a light bulb -- they will emit a good deal of visible light.
The filament in a light bulb is made of a long, incredibly thin length of tungsten metal. In a typical 60-watt bulb, the tungsten filament is about 6.5 feet (2 meters) long but only one-hundredth of an inch thick. The tungsten is arranged in a double coil in order to fit it all in a small space. That is, the filament is wound up to make one coil, and then this coil is wound to make a larger coil. In a 60-watt bulb, the coil is less than an inch long.
Tungsten is used in nearly all incandescent light bulbs because it is an ideal filament material. we'll find out why this is, and we'll examine the role of the glass bulb and inert gas.
a metal must be heated to extreme temperatures before it will emit a useful amount of visible light. Most metals will actually melt before reaching such extreme temperatures -- the vibration will break apart the rigid structural bonds between the atoms so that the material becomes a liquid. Light bulbs are manufactured with tungsten filaments because tungsten has an abnormally high melting temperature.
But tungsten will catch on fire at such high temperatures, if the conditions are right. Combustion is caused by a reaction between two chemicals, which is set off when one of the chemicals has reached its ignition temperature. On Earth, combustion is usually a reaction between oxygen in the atmosphere and some heated material, but other combinations of chemicals will combust as well.
The filament in a light bulb is housed in a sealed, oxygen-free chamber to prevent combustion. In the first light bulbs, all the air was sucked out of the bulb to create a near vacuum -- an area with no matter in it. Since there wasn't any gaseous matter present (or hardly any), the material could not combust.
The problem with this approach was the evaporation of the tungsten atoms. At such extreme temperatures, the occasional tungsten atom vibrates enough to detach from the atoms around it and flies into the air. In a vacuum bulb, free tungsten atoms shoot out in a straight line and collect on the inside of the glass. As more and more atoms evaporate, the filament starts to disintegrate, and the glass starts to get darker. This reduces the life of the bulb considerably.
In a modern light bulb, inert gases, typically argon, greatly reduce this loss of tungsten. When a tungsten atom evaporates, chances are it will collide with an argon atom and bounce right back toward the filament, where it will rejoin the solid structure. Since inert gases normally don't react with other elements, there is no chance of the elements combining in a combustion reaction.
Cheap, effective and easy-to-use, the light bulb has proved a monstrous success. It is still the most popular method of bringing light indoors and extending the day after sundown. But by all indications, it will eventually give way to more advanced technologies, because it isn't very efficient.
Incandescent light bulbs give off most of their energy in the form of heat-carrying infrared light photons -- only about 10 percent of the light produced is in the visible spectrum. This wastes a lot of electricity. Cool light sources, such as fluorescent lamps and LEDs, don't waste a lot of energy generating heat -- they give off mostly visible light. For this reason, they are slowly edging out the old reliable light bulb.
2 To read about black body radiation
3 How CFL works?
CFL
(Compact Fluorescent Lamp) converts electrical energy to radiant
energy. They are energy efficient and use better technology as compared
to conventional tube lights and bulbs. It has two components:
a) A glass tube filled with argon and mercury vapor & coated with a layer of fluorescent material.
b) An electronic ballast circuit.
CFLs contain argon and mercury vapor housed within a spiral-shaped tube.
They also have an integrated ballast, which produces an electric
current to pass through the vaporous mixture, exciting the gas
molecules. In older CFLs, it took several seconds for the ballast to
produce enough electricity to ramp up the excitation. Newer CFLs have
more efficient ballasts and require a shorter warm-up. Either way, when
the gas gets excited, it produces ultraviolet light. The ultraviolet
light, in turn, stimulates a fluorescent coating painted on the inside
of the tube. As this coating absorbs energy, it emits visible light.3 What is meant by non ionizing radiation?
Non-ionizing (or non-ionising) radiation refers to any type of electromagnetic radiation that does not carry enough energy per quantum to ionize atoms or molecules—that is, to completely remove an electron from an atom or molecule. Instead of producing charged ions when passing through matter, the electromagnetic radiation has sufficient energy only for excitation, the movement of an electron to a higher energy state. Nevertheless, different biological effects are observed for different types of non-ionizing radiation
Electromagnetic radiation, the photons of which lack the energy required to ionize atoms or induce ion formation; NIR includes sound, ultraviolet, visible, and infrared light, microwaves, and radiowaves. Cf Ionizing radiation.
4 Which are the types of UV lights? Where all we use UV light?
There are three types in UV Lights, 1) UV-C, 2)UV-B, 3)UV-A
1) UVC - shortwave UV, which includes germicidal ultraviolet at 253.7nm wavelength - is used for air, surface and water disinfection. Unintentional overexposure to UV-C causes skin redness and eye irritation, but does not cause skin cancer or cataracts.
2) UV-B - A small, but dangerous part of sunlight. Most solar UV-B is absorbed by the ozone layer. Prolonged exposure causes sun burn and could result in unhealthy effects on the skin and eyes.
3) UV-A - Long wave UV causes premature skin aging.
9 To read about absorption spectra, emission spectra, hydrogen spectra, EPROM..
10 Difference between dose and intensity
11 Probability calculation in PCB
12 Transistor specifications
Subscribe to:
Posts (Atom)
